StarWind Software

After first host added iSCSI disk, the second host was not able to mount the same iSCSI disk. At the last step, got a error message:

Cannot change the host configurate.

After alternated between 2 hosts, the result was same.

Each host only has one cable, is it the reason?

Thanks!

George

If you are using basic image device you need to enable clustering (multiple connections) to it. You can do it following way: You can do even following way: stop vmdk, go to %Program Files%/StarWind Software/StarWind/starwind.cfg and find chapter <devices>, find there your device, and change value clustered="no" to clustered="yes". Then open CMD and type:
net stop starwindservice
net start starwindservice.

[quote=" stop vmdk.[/quote]

How can I do it?

Thanks!

Sorry, stop VM

Sorry, I have 2 hosts not VMs want to do it.

I changed clustered="no" to "yes" at 5 points on CFG. Is 5 points right?
After I did it, the first host can get the iSCAI HD but Second host. Doing rescan on Storage menu in vCenter Server many times, the second host can't find out any Devices on iSCSI server. Why?

As you know, before I changed the CFG, the second host can find out all Devices on iSCSI server but can't mount the devices on iSCSI(please read my first page above). But, it can't find out any Devices on iSCSI server now.

Can't the MCSC way be used to make cluster between 2 VMware hosts? Should use New Cluster in vCenter Server to configure cluster between 2 VMware hosts?

Hi, I think that there can be ceatain misunderstanding in this thread, we miss some critical stich which causes the whole mess
Could you be so kind to deop me an e-mail (max@starwindsoftware.com) so I'll be able to arrange a screensharing session for fixing this.

Hi Max,

your email address max@starwindsoftware.com is unavailable. my Email was returned. please send an email to me at georgeyu100@hotmail.com.

Thanks!

George Yu

Just sent an E-mail to you, please check your inbox.

Hi Max,

I reanswered you email afew time. But, it was hard to reach me. please give me a call at (403)264-8986?


This is an automatically generated Delivery Status Notification. Delivery to the following recipients failed. max@starwindsoftware.com


--Forwarded Message Attachment--
From: georgeyu100@hotmail.com
To: max@starwindsoftware.com
Subject: FW: Delivery Status Notification (Failure)
Date: Mon, 13 Sep 2010 19:24:43 -0600








again!



George







--------------------------------------------------------------------------------

From: georgeyu100@hotmail.com
To: max@starwindsoftware.com
Subject: FW: Delivery Status Notification (Failure)
Date: Thu, 9 Sep 2010 09:31:29 -0600




again!



From: postmaster@mail.hotmail.com
To: georgeyu100@hotmail.com
Date: Thu, 9 Sep 2010 07:28:48 -0700
Subject: Delivery Status Notification (Failure)


This is an automatically generated Delivery Status Notification. Delivery to the following recipients failed. max@starwindsoftware.com


--Forwarded Message Attachment--
From: georgeyu100@hotmail.com
To: max@starwindsoftware.com
Subject: FW: Delivery Status Notification (Failure)
Date: Thu, 9 Sep 2010 08:28:41 -0600







again


From: postmaster@mail.hotmail.com
To: georgeyu100@hotmail.com
Date: Thu, 9 Sep 2010 07:26:11 -0700
Subject: Delivery Status Notification (Failure)


This is an automatically generated Delivery Status Notification. Delivery to the following recipients failed. max@starwindsoftware.com


--Forwarded Message Attachment--
From: georgeyu100@hotmail.com
To: max@starwindsoftware.com
Subject: RE: Second vShere host can't add iSCSI disk
Date: Thu, 9 Sep 2010 08:26:02 -0600



Ok. my timezone is mountain time (-7)

thanks!

George

Thanks for update! Max or Tommy Lo (US Support Engineer) will call you today.