yaroslav (staff) wrote:Hi,

Thanks for more details on this case!

Go to SyncHaDevice.ps1 -> comment $device.Synchronize([SwHaSyncType]::SW_HA_SYNC_FULL, "") -> uncomment #$device.MarkAsSynchronized().

Did you try this one?

Have a great weekend!

Thanks a lot sir ...


This worked for me..

Hi, Thanks for more details on this case! Go to SyncHaDevice.ps1 -> comment $device.Synchronize([SwHaSyncType]::SW_HA_SYNC_FULL, "") -> uncomment #$device.MarkAsSynchronized(). Did you try this one? Have a great weekend! No sir Tomorrow I wil try and let you know the results sir.

Do you have HA devices or Image devices? If so, those are to be listed nearby <targets> section (where their targets are listed). I have HA Devices sir.. What I observed is, I used trial license even in this case when one VM/NODE is switched it will be in Not Synchronised state but when I mark it a...

yaroslav (staff) wrote:See my previous comment or point refer the target to the imgfile, not HA device in StarWind.cfg.

I dint get anything in StarWind.cfg file sir.

Can you please help me out what to do.

To mark manually as synchronized 1. Stop StarWindService on all nodes. 2. Go to *_HA.swdsk 3. Set <sync_status>1</sync_status> for the HA device you need to mark as synchronized and <sync_status>0</sync_status> 4. Repeat appropriate changes for the opposite node. 5. Start the service. If one node i...

To mark manually as synchronized 1. Stop StarWindService on all nodes. 2. Go to *_HA.swdsk 3. Set <sync_status>1</sync_status> for the HA device you need to mark as synchronized and <sync_status>0</sync_status> 4. Repeat appropriate changes for the opposite node. 5. Start the service. If one node i...

To mark manually as synchronized 1. Stop StarWindService on all nodes. 2. Go to *_HA.swdsk 3. Set <sync_status>1</sync_status> for the HA device you need to mark as synchronized and <sync_status>0</sync_status> 4. Repeat appropriate changes for the opposite node. 5. Start the service. If one node i...

One more question raised in me.

If one of my node is down with hard disk failure or any other failure and to be bought up with only fresh installation while another node is either in Synchronised or in Non Synchronised state.. how to create HA between existing node and newly installed node???

Please review the SyncHaDeviceAdvanced.ps1. I tried with SyncHaDeviceAdvanced.ps1 and also SyncHADevice.ps1 but dint workout. I tried with SyncType 1, 2 and 3 also but it was throwing error saying partner iSCSi target didn't found. What is the Type of sync to be used sir?? Did you try shutting down...

Hi sir, Thanks for the response. I have removed the Write Back Cache. Today's Observation after removal of Write-Back Cache. Case 1: Previous State of VMs - Both VMs are Off. When any 1 of the Node is switched On the storage volume will be in Not Synchronised state, storage will not be available and...

The software tries to avoid synchronization running in the wrong way, so it either lets user to launch full synchronization or waits partner to confirm its own status. Sir, Then incase of outage, by running synchronisation or advanced synchronisation script will bring my storage online?? Try shutti...

Hi sir, Thanks for the response. Before the restart, did you check the iSCSI paths to be connected and active (make sure ALL the mirrors are available under Storage -> Storage Adapters -> Software iSCSI)? Please also make sure the rescan script is set up and working fine. Yes sir, iSCSI paths to be ...

Before Shutting down the server I ensured all the 3 Volumes were successfully synchronised between nodes. Synchronisation happened from Node 1 to Node 2. When I started Node 2 the storage was not available but when I started Node 1 storage was available and again synchronisation started from Node2 t...

Hi Team, I have configured StarWind Virtual SAN for vSphere 2-Node Hyperconverged Scenario with VMware vSphere 8. I have created 3 Volumes (attached code for reference). The Storage is working fine, Node1 had 1st Priority and Node had 2nd Priority. But during testing i made Shutdown both the servers...

Can I have the logs, and the new script, please? Latest Code and Logs are attached. Kindly highlight my mistake sir. Setup Starwindvsa_Setup.png Latest Code param($addr="10.10.184.234", $port=3261, $user="root", $password="starwind", $addr2="10.10.184.235", $...